Adhere

Adhere - hurtig herdende og brukes til å lime på sko og til hovreparasjoner Fås i Sort eller beige

PrisNOK489,00 inkl. mva.
  • Produktinfo
  • Produktanmeldelser (0)
Adhere - hurtig herdende og brukes til å lime på sko og til hovreparasjoner
- Herder raskt, men gir deg tid nok til å lime på en sko
- Tillater hovbevegelsene i draktene
- Er tidsbesparende ved hovreparasjoner
 
PRODUCT INFORMATION
 
Fast-setting urethane adhesive designed to bond steel, aluminum and urethane shoes to the hoof and to
fabricate hoof wall repairs. Available in 180cc Cartridge.

• Glue on steel, aluminum and most plastic shoes as well as any hoof repair project
• Initial set time of 1 minute and final cure time of 6 minutes
• Perfect for most every application
• Adhere™ sets hard with a superior bond, but maintains the flexibility necessary at the quarters and heels
  to allow the natural movement of the hoof
 
Instructions
Adhere 180cc Cartridge
PLEASE NOTE BEFORE APPLYING PRODUCT
• Vettec products are best used between 65° and 85° F (18° to 29° C). Temperature will affect the set time.
  See Cold & Hot Conditions below.
• Areas of wetness or bleeding should not be covered. Once healed, commence using products.
• Adhere can be applied with the shoe on or off, but will bond to the shoe. A coating of oil or petroleum jelly to the
  top of shoe will prevent this from occurring. Take care not to get any on the area of the hoof being repaired.
• Product may not bond to hooves that have been heavily treated with products containing: oils, grease, pine tar,
  etc. In these instances a thorough
denatured alcohol scrub and drying should be performed to ensure adhesion.
• The following procedures are best-accomplished wearing latex or rubber gloves.
• Do not burn or
“Hot Shoe” this product.
• Use only Vettec mixing tips.

COLD CONDITIONS (Below 65° F)
• Failure to keep the hooves, shoes and product warm will dramatically slow the cure time. Example: At 32° F
  the cure time advances 7 - 8 minutes.
Do not microwave the cartridge or place it in water. Store the cartridges in an insulated “cooler” warmed with
  microwavable heat pads or 1 to 2 tightly capped gallon jugs filled with hot water.
• In freezing temperatures, 32° F or less, the shoes must be warmed to keep condensation from forming on them   and preventing the bond.

HOT CONDITIONS (Above 85° F)
• Product will set very quickly. To retard the set time, store the material in an insulated cooler with 1 or 2
  freezer packs.
NOTE: During hot weather conditions, product may cure at a higher temperature. Under these circumstances
  when temperature is an issue, product may be applied in layers to reduce heat.

CARTRIDGE PREPARATION
1. To open the cartridge, remove the tip at line with nippers. Insert cartridge into dispensing gun, label side up.
2. Before attaching the mixing tip, equalize the cartridge by squeezing out a small amount to ensure that both
    sides are dispensing evenly.
3. Attach a mixing tip by pressing and twisting clockwise.
4. When finished, do not release the pressure with the lever on the back of the dispenser. Remove the mixing
    tip immediately, discard and replace the cap. The pressure can now be released. Caps are available from
    your dealer.
5. For additional applications, re-equalize the cartridge and attach a new tip.

HOOF PREPARATION
1. Trim and balance the hoof and conservatively pare the sole. Remove any weak or soft material that will
    exfoliate in the next 2-3 weeks, especially at the white line area.

2. Using a hoof knife trim and clean the frog, bars and commissures. Remove all loose sole and dirt with a
    wire brush.
3. Pay special attention to the bars. The bars should not be lying over onto the sole as this could cause a
    pressure point. If the bars are lying down, trim them back to proper position.
4.
NOTE: Only if hoof is oily, wipe the affected areas with a cloth moistened with denatured alcohol being careful
    not to saturate the hoof.
Do not use acetone!
5. Have all materials ready
(including contouring plastic and prepare the cartridges) before proceeding to the
    next step.
6. Holding sole upward
dry hoof thoroughly using a heat gun for 30-45 seconds. Do not overheat. Keep heat
    source approximately 6 inches away from sole.
    NOTE: All hooves contain natural moisture and must be dried exactly in the manner described above.
    This step is critical for the product to achieve the appropriate bond to the sole.

SHOE PREPARATION
1. Clips are highly recommended for stability and accurate placement of the shoe. Have clips set before gluing.
2. Drill a 5/16” hole between the second and third nail holes of both branches, beveled on the ground side.
    If possible, enlarge the other nail holes also using a drill or pritchel.
3. Grind or rasp the top of the shoes to remove oxidation and roughen the surface. Clean with denatured alcohol
    to remove oil, grease, slag, dirt, and dry thoroughly.
4. Place 3 to 4
Adhesive-Spacers (REF #46025) or pieces of wooden matchsticks around the web of the shoe to
    maintain approximately 1/8” space for Adhere.
Optional: Apply Duct tape to the last 1” to 1 1/2” of the branches. This will prevent Adhere from locking the heels.

APPLICATION PROCEDURE - GLUEING ON SHOES
1. Apply Adhere to the shoe approximately 3/8’’ thick and the width of the shoe.
2. Quickly and accurately place the shoe. Adhere will set in approximately 1 minute.
3. Keep the hoof elevated taking care not to move the shoe for 3 1/2 minutes until the Adhere cures.
    HINT: Wrap the hoof & shoe with pallet wrap after 1 minute and set down. Remove wrap later.

APPLICATION PROCEDURE - HOOF REPAIR
1. Follow hoof preparations instructions above.
2. Trim, rasp, balance, and clean the hoof around the damaged area.
3. Using a hoof knife or Dremel™ tool, rout out the damaged areas.
4. Create an undercut on the hoof wall.
5. Protect the coronary band with hoof tape or damp gauze.
6. Clean and thoroughly dry the prepped area per instructions. If wet conditions exist, horse should be stalled
    overnight with dry bedding.
7. Dispense Adhere directly into damaged area over-filling around the repair and onto sound hoof wall. Do not
    feather or "thin-out" the material around the edges. This will slow the set time and can lead to failure.
    Contouring Plastic (REF #46904) can be utilized to push the material into the void. Leave in place until Adhere
    cures and then peel off.
8. Allow a working time of 55 seconds for molding and shaping.
9. Allow 7 to 8 minutes for a full cure and then shape by trimming and rasping toward the hoof.
10. Nail shoe on. Nails will penetrate without damaging the repair.
11. If necessary, after rasping and shoeing, fill any voids or holes

Download Instruction PDF: English | French | Spanish

For professional use only. Keep out of reach of children.

Skriv en produktanmeldelse og del dine erfaringer med dette produktet med andre kunder.